SPS MID-POWER AND HPS COMMON SPECIFICATIONS

TECHNICAL SPECIFICATIONS The following subsections provide environmental, electrical, and physical characteristics for the SPS MEDIUM POWER Series power supplies.  Environmental Characteristics Parameter Specification Temperature Coefficient 0.02%/°C of maximum output voltage rating for voltage set point. 0.03%/°C of maximum output current rating for current set point. Ambient Temperatures Operating 0 to 50°C Storage -25° to 65°C Cooling Internal fans; vents on sides and rear. (Units may be stacked without clearance above or below). Humidity 95% maximum, non-condensing, 0 to 50°C; 45°C maximum wet-bulb temperature Altitude Operating full power available up to 5,000 feet (1,524m), derate 10% of full power for every 1,000 feet higher; non-operating to 40,000 feet (12,192m) Ozone concentration Recommended long-term exposure limit is 0.1 PPM (0.2 mg/m3).  Electrical Characteristics Parameter Specification Input Power Voltage (Standard)  208/220 VAC±10% (allowed range 187-242 VAC) Voltage (Options)  380/400 VAC±10% (allowed range 342-440 VAC) 440/480 VAC±10% (allowed range 396-528 VAC) Frequency  47 to 63 Hz Phases  3–phase, 3–wire plus ground. Not phase rotation sensitive. Neutral not used. Power Factor  0.9 typical for 208/220VAC input0.78 typical for 380/400VAC input0.7 typical for 440/480VAC input Efficiency  87% typical at full load, nominal line Front Panel Meter Accuracy   Voltage ±0.15% of full-scale   Current ±0.4% of full-scale Load Regulation (Specified at no load to full load, nominal AC input)   Voltage 0.02% of maximum output voltage   Current 0.1% of maximum output current Line Regulation (Specified ±10% of nominal AC input, constant load)   Voltage 0.01% of maximum output voltage   Current 0.05% of maximum output current Transient Response A 50% step load will recover to within 0.75% of original value within 1 ms. Down Programming With no load the output will program from 100 to 10% in less than 1.5 seconds Stability ±0.05% of set point after 8–hr. warm-up at fixed line, load, and temperature using remote sense Remote Control/Monitor On/Off control via contact closure, 6-120 VDC or 12-240 VAC, and TTL or CMOS switch, output voltage and current monitor, OVP limit set, summary fault status Parameter Specification Front panel and remote digital programming Voltage ±0.1% of full-scale output Current ±0.4% of full-scale output Overvoltage Protection (OVP) ±1% of full-scale output REMOTE DIGITAL READBACK Voltage ±0.15% of full-scale output Current ±0.4% of full-scale output Remote ANALOG Programming   Constant Voltage   ±0.25% of full-scale output for 0-5V range (±0.5% 0-10V range)   Constant Current   ±0.8% of full-scale output   Overvoltage Protection (OVP) ±1% of full-scale output REMOTE ANALOG READBACK Voltage ±1% of full-scale output, 0-10V range Current ±1% of full-scale output, 0-10V range Resistive   Constant Voltage (0-100%) 0–5 kΩ   Constant Current (0-100%) 0–5 kΩ Voltage   Constant Voltage (0-100%) 0–5 VDC or 0–10 VDC   Constant Current (0-100%) 0–5 VDC or 0–10 VDC   Overvoltage Protection (OVP) (5–110%) 0.25–5.5 VDC Remote Sensing Terminals are provided to regulate output voltage at point of load. Maximum line drop 5% of rated output voltage per line for 40-100V models, 2% of rated output voltage per line for >100V models. REMOTE ANALOG CONTROL   Input to Output Isolation   The control signal return for Non-Isolated Analog programming is connected to the negative output terminal. Under no condition should the negative terminal exceed 300V to earth ground. The maximum voltage from control signal return of the Remote Isolated Analog programming (option) to the negative output terminal is 600V. Dimension 3U Models 6U Models Width 19.00 in (48.3 cm) 19.00 in (48.3 cm) Depth 25.46 in (64.7 cm) 25.12 in (63.8 cm) Height 5.25 in (13.3 cm) 10.5 in (26.7 cm) Weight (5kW) ≈ 40 lbs (18 kg) (20 KW) ≈ 120 lbs (54 kg) (10kW) ≈ 60 lbs (27 kg) (25 kW) ≈ 140 lbs (64 kg) (15kW) ≈ 80 lbs (36 kg) (30kW) ≈ 160 lbs (73 kg) Important Notes:  Specifications are subject to change without notice The SPS Series power supplies are intended for indoor use only.